LosDSC1Energy must be supplied efficiently and practically, and inverters must be small and portable to allow their use where there is no mains electricity connection and where a backup power supply is essential in case of emergency. These types of inverters must also be characterized by their ease of use and on-site maintenance.


The customer's inverter accepts a nominal battery voltage of 24V or 48V, weighs only 8kg, and delivers a nominal output power of 2200 VA with a maximum efficiency of 93%. Combining the charging technology and inverter into a single unit achieves two objectives: compact size and portability. The customer utilizes an inverter architecture based on a high-frequency transformer, comprising an input high-frequency power stage, a high-frequency transformer, an intermediate DC link, and an output power stage. The standalone inverter is based on a small, high-frequency transformer, quite unlike the bulky, low-frequency transformers often used as an alternative.


The high-frequency concept means that the loads connected to the inverter are connected almost directly to the output stage without the attenuation often present in low-frequency transformer-based designs. Therefore, all fluctuations on the load side can be regulated through the power stage at the output. Implementing this architecture with efficiency and a high-quality output waveform that met the specifications for frequency, voltage, and harmonic distortion presented a significant design challenge.


Connecting and switching standalone inverters in parallel on the AC side presented a significant challenge because a standalone inverter functions as a voltage source. This means it generates its own stable output voltage and regulates the current according to the connected loads. Therefore, when two or more voltage sources are connected but not synchronized, the loads are unbalanced, and current flows between the sources, resulting in power losses and zero active power. This current flow can also negatively impact the power sources.


A small phase shift between two voltage sources can also cause this asymmetrical situation, resulting in a voltage difference between them that can establish a direct connection between the voltage sources on the AC side. This occurs due to their very low resistance, which in turn produces a very high current flow between the inverters. The client implemented a very fast and accurate control and communication algorithm to resolve this issue.


A modular design concept addressed the operational requirements of several stand-alone inverters in parallel. A backup inverter functions as a standard (DC/AC) inverter and charges the batteries from an AC (AC/DC) source; the same power electronic circuitry serves as a generator. Since the market currently lacks inverters offering this functionality and they are based on a high-frequency transformer architecture, a completely new interface and control strategy was necessary. Figure 1 illustrates the client's proposal for an inverter system comprised of four different functional blocks served by three different signal controllers: DC/DC, DC/AC, and a Display and User Interface.


The customer searched among Digital Signal Controllers (DSCs) and selected dsPIC DSCs, which have power supply-compatible peripherals such as counter-based PWM (Pulse-Width Modulation) modules, analog comparator-based feedback sampling, and coordinated A/D converters, along with fast multiplication in a single clock cycle. These dsPIC30F DSCs can provide the high execution speeds required by the closed-loop algorithms for the customer's inverters.


No external components, such as a reset controller, memory chips, an A/D converter, or a CAN (Controller Area Network) controller, were needed, as they are integrated into the DSCs. The dsPIC30F DSCs offer execution speeds of up to 30 MIPS and ensure increased efficiency and reliability in the inverter system. Their easy upgradeability is another advantage, as the DSCs can operate within a wide voltage range of 2.5V to 5.5V.


The inverter design was flexible and modular; the DSCs offered various Flash and RAM capacities, as well as diverse connectivity options. In the DC/DC power stage block, the dsPIC30F5015 DSC controls the high-frequency stage between the battery input and the high-frequency transformer. This device was also used to accurately measure the battery voltage and current. In the DC/AC power stage, the dsPIC30F6010A handled the power electronics circuitry by means of a patent-pending Proportional-Integral (PI) control loop.


LosDSC2For the instrument panel and inverter display controls, the dsPIC30F6010A connects to the dsPIC30F5011 via the CAN bus. It also adjusts the inverter's operating modes according to user instructions. The dsPIC30F5011 incorporates 66 KB of Flash memory and a CAN interface, and the integrated Flash memory helps store all the graphic icons for the inverter's multilingual user interface. Users can navigate through the different operating modes and menus using the navigation keys located on the panel.


These highly stable, fast-response inverters, based on high-frequency transformer technology and featuring a modular design, can be connected in parallel. Up to five additional inverters per phase can be connected in parallel for three-phase operation, for a total of 15 inverters in a system.


The client was able to design a compact and multifunctional inverter that allows autonomous power supply without the need for connection to the public electricity grid thanks to Microchip's dsPIC30F DSCs.

 

Note: The Microchip and dsPIC names and logos are registered trademarks of Microchip Technology Inc. in the U.S. and other countries. All other trademarks mentioned belong to their respective companies.


Author:

Victor Alcazar,
Director of Market Development,
High-Performance Microcontrollers Division,
Microchip Technology Inc.


More information or a quote