In this situation, or when we encounter problems addressing the stress and aging that can occur on a component or board subjected to high temperatures, expert advice can offer suitable solutions for each case. The team of engineers at Steliau Technology's Thermal & Adhesives division, with experience dating back to 1992, brings the latest technology to verify the suitability of solutions, along with the equipment to design and manufacture fully customized solutions for the application.

Why a TIM?
Materials are not perfectly smooth (Figure 1) when we look at the cross-section of the component and radiator joint under a microscope. Even when we press one material against the other, we can see that irregularities form small air bubbles between the two surfaces, and the contact is not as direct as it appears to the naked eye.

Since the thermal conductivity of air is very low compared to other materials, it is necessary to eliminate it, as well as to homogenize the surface so that there are no contact points, but rather a smooth contact surface. We achieve this by using a TIM, which is essentially a thermal material whose physical characteristics allow it to conform to the nanometric irregularities of the surfaces.


What information is needed to choose a TIM (Temperature Insulation Material)?
At this point, we encounter the dilemma of what type of material to use. The answer isn't easy. If we look at the Steliu Technology catalog, they have 2,000 references in stock, and the selection depends not only on the material's thermal conductivity when we want to dissipate heat, or its thermal resistance when we want to insulate (Figure 2), but also on factors such as:
Contact pressure,
surface roughness,
whether the surface is perfectly flat (height difference between components on the PCB),
time,
temperature,
material thickness (t/k),
and filler attributes.

Therefore, before deciding which material to use, we must answer certain questions:
- What are the components between which the TIM is located? "Component to be cooled and heatsink that has been chosen."
- Are the components in contact, or is there a gap to fill?
- What is the thickness of the gap between the component and the heatsink? Nominal + minimum and maximum tolerance.
- How is the component mounted on the heatsink? Screws, clips, etc.
- Are there any available 3D printed templates and/or dimensions for the TIM? This allows us to create a custom-fit element for the component, depending on the materials used, which will save material and cost, as well as guarantee the quality of the final product.
- What is the total heat/power (in W) of the component that needs to be dissipated?
- Is a specific rth or thermal conductivity value expected for the TIM?
- Is electrical insulation required?
- Project data (UAE/SOP), sample/proto, and L/T.
With this information, we can decide which TIM range to use:
Thin interface pads are a standard product with high thermal conductivity, with performance levels of 0.8–3.0 W/mK, reinforced with film and fiberglass, and may or may not contain silicone, with electrically conductive or insulating versions. They are commonly used in applications requiring high dielectric strength, but it should be noted that they require firm pressure to maintain effectiveness.
A key advantage is that pads can be designed in the shape or size required by the application; Steliau Technology has a design team and machinery to meet the specific needs of each team.
Phase-change pads, where the material's viscosity changes with temperature, are available in various forms depending on the product range. These pads change viscosity at 50-60°C, or they are high-performance greases. This variety offers a performance range of 1.0-4.0 W/mK, making it suitable for high-performance computing applications. However, the assembly process must be carefully considered, including the placement of screens, templates, and pads, as well as electrical insulation requirements.
Thermally conductive putty is another standard product with performance levels between 1.0-8.0 W/mK. It is available as a two-component, self-curing material or as a single-component, pre-cured material. Both formats are available with and without silicone.
Its use is recommended for high-volume production; for optimal efficiency, a material dispenser is necessary.
The key advantage of this solution is that the pressure exerted on the TIM (Temperature Immobilizer) has virtually no effect on its deflection compared to conventional pads (Figure 3).

These materials are evolving thanks to research into new materials, offering greater heat dissipation and greater softness, or, consequently, greater reworkability.
Gap Pads (Figure 4) are pads that allow not only heat dissipation but also leveling of areas in mixed component layouts on a PCB. Standard materials are available with efficiencies between 0.8 and 20.0 W/mK and thicknesses up to 6.5 mm, both silicone-based and silicone-free. Their design is customized to the application, both in terms of shape and thermal conductivity.
One of the advances being promoted in the materials industry is the combination of thermal performance with EMI absorption, making these types of solutions very attractive for all kinds of applications.

Applications and Support:
With this variety of thermal performances and material solutions, the applications of these components range from the power segment with power supplies, DC/DC converters, battery chargers, UPSs, induction elements, pumps, and EV equipment to heat dissipation for power LEDs, induction elements, household appliances, and much more. They cover vertical markets such as industry, medical, defense, aerospace and telecommunications, lighting, and transportation.

Each market and application has its own unique characteristics. With 20 years of experience, the Steliau Technology team has amassed expertise and know-how that allows them to reduce product development costs, offer CFD analysis and consulting services for optimal thermal solutions, and provide support for new products requiring thermal solutions or for existing products with malfunctioning components.

Thanks to the simulation software (Figure 6) they have, they are able to perform thermal modeling and use advanced computational fluid dynamics (CFD), creating accurate models of electronic equipment that allow for specific designs for the electronics industry. This software adapts to overcome the challenges of thermal design, helping the team led by three specialized engineers from the Thermal & Adhesives division of Steliau Technology-EUROPE to provide unbeatable solutions.

By Lionel Girardot BU Manager Thermal & Adhesives at Steliau Technology-EUROPE