This article explains the need for a battery management system in an electric vehicle, describes a typical architecture, and investigates the main components used to detect, monitor, and manage the overall health of an electric vehicle battery pack.
Anatomy of an Electric Vehicle Battery
The primary power source for an electric vehicle is a battery pack (Figure 1). The pack is typically designed to fit under the vehicle, between the front and rear wheels, occupying the space normally reserved for the transmission tunnel, exhaust pipe, and fuel tank in an internal combustion engine vehicle. Keeping the pack as low as possible significantly lowers the center of gravity, an essential factor in the vehicle's on-road handling characteristics.

Figure 1: Battery pack of an electric vehicle (source: Nissan).
For the next generation of electric vehicles, a consortium of manufacturers is studying the development of an interchangeable battery pack that can be adapted to different vehicle platforms and quickly removed and replaced with a fully charged unit. However, the logistical and technical considerations are costly, and progress has slowed.
An electric vehicle battery pack consists of several modules, each containing multiple cylindrical or pouch-type lithium batteries. The cells are arranged in a combination of series and parallel configurations to provide a power output of 400 or 800 V. Currently, 800 V packs are preferred, primarily because they allow for a faster charge cycle at a given current. Each cell operates between 2.5 and 4.2 V (depending on its chemical composition), and the behavior of each cell influences the overall effectiveness and efficiency of the battery pack. Therefore, a prerequisite is the control and management of the cells with a battery management system (BMS).
Key Criteria for Managing Battery Health:
Lithium-ion cells are renowned for their excellent discharge characteristics, enabling electric vehicles to accelerate like high-performance sports cars. However, these impressive discharge capabilities pose a significant safety risk in the wrong situation. The high output voltage of the battery pack also presents a risk to the driver, passengers, and anyone else involved in an accident. Compliance with relevant legislation on functional automotive safety is crucial and constitutes another task on the list of requirements for the battery management system. Figure 2 illustrates the key battery health parameters that the BMS monitors and controls.

Figure 2: The BMS monitors the health of the battery pack and controls the operation of cell balancing and emergency safety functions (source: University of Warwick, Advanced Propulsion Centre).
The key metrics of a BMS are as follows:
- Estimated State of Charge (SOC): SOC indicates the remaining energy in an electric vehicle at any given time and is usually expressed as a percentage of the total capacity. SOC is a fundamental metric, as it tells the driver how much charge is left and allows them to estimate the vehicle's potential range. Several sensors connected to the BMS provide the necessary information to the algorithms running on the BMS's microcontroller to estimate the state of charge.
- State of Health (SOH): SOH, also specified as a percentage, indicates the overall health and capacity of the vehicle's battery pack compared to its original capacity when new. It is a measure of the battery pack's ability to store and deliver energy over time, taking into account cell aging due to repeated charge and discharge cycles, as well as chemical changes within the cell.
- State of Function (SOF): SOF takes into account State of Health but provides a more realistic understanding of the pack's ability to deliver energy under a range of operating conditions. Factors influencing the SOF include internal cell resistances, the thermal behavior of the battery pack, and cell voltages. The SOF helps determine how to optimize the cell and the pack, and whether maintenance or pack replacement is necessary.
An important battery optimization technique is cell balancing. Due to the chemical composition of cells, slight differences exist in their performance and aging, creating an imbalance in output voltage and capacity during discharge. Cell balancing is based on equalizing the charge across all cells to optimize overall performance and extend battery life. Voltage and current control by the Battery Management System (BMS) aims to achieve a uniform State of Charge (SOC) and prevent overcharging or undercharging of individual cells.
Other BMS functions include thermal management, overcurrent protection, and additional functional safety features (e.g., according to ISO 26262) and safety integrity features (e.g., according to ASIL-D).
Another important aspect of electric vehicle battery packs is thermal management. Monitoring cell temperature increasingly involves placing sensors in various locations within the cell, rather than simply on the outer casing or in a central location within a cell module. Localized hot spots can indicate an impending cell failure that can spread to surrounding cells, potentially leading to thermal runaway and a fire. In cold environments, battery performance is compromised, so the BMS needs to actively regulate charging to prevent permanent cell damage. Active thermal cooling and heating techniques may be necessary for electric vehicles designed for continuous operation in extreme environments.
If a cell fails to hold a charge or exhibits poor performance, the BMS can isolate the cell to prevent further damage or an impact on the overall performance of the module and battery pack.
Typical Battery Management System Architecture:
Figure 3 illustrates the high-level architecture of a BMS for a common electric vehicle. The integrated hardware functions fall into four categories: sensors, cell management ICs and microcontrollers, onboard networks, and safety and isolation. In terms of software, battery management algorithms estimate a realistic state of charge.

Figure 3: The architecture of a typical battery management system used in an electric vehicle (source: Mouser Electronics).
Sensors (voltage and current control): The exact method of voltage control varies, but the most efficient bill of materials system uses only one sensor signal chain, which employs an op-amp and an analog-to-digital converter (ADC). Each cell and module feeds individual voltage sensor wires, and a multiplexer circuit switches the cell's input value to the signal chain. A similar method is used for current detection, in which the voltage drop measured across an extremely low-value shunt resistor within the battery module is read. This system, shown in Figure 3, performs the necessary control task without adding complexity to the circuitry of each cell and module.
Sensors (temperature): For cell control applications, simple thermistors are available using digital output temperature sensors. Thermistors are a cost-effective option and take up very little space within a battery module. As noted earlier, research into more sophisticated cell control techniques, using multiple temperature and magnetic field sensors placed within each cell, enables more detailed cell management.
Cell management ICs and microcontrollers: Highly integrated cell management and control ICs are available for electric vehicle applications and offer a cost-effective, performance-optimized alternative to general-purpose microcontrollers. Most provide all the necessary analog signal chain functions for monitoring voltage, current, and temperature. Some are also equipped with MOSFET cell balance controllers to achieve active cell balancing during charging and discharging. Other integrated features include network connectivity for Ethernet and CAN interfaces with other vehicle systems. Battery management algorithms provide a more informed and adaptive approach to optimizing battery pack performance under load and overall health conditions.
Isolation and safety: Safety features range from the "get me home" function, which provides limited battery capacity to the drivetrain, to complete galvanic isolation of the battery pack from all electric vehicle functions. The latter uses single-use pyrotechnic circuit breakers that employ a small explosive charge, called a squib, to instantly interrupt the high-voltage output of the battery. The squib breaks the circuit much faster than the typical breakdown time of a conventional fuse.
BMS Component Display:
An example of a multi-cell battery control and balancing IC is the L9963E from STMicroelectronics. The automotive-grade AEC-Q100 certified L9963E IC can monitor the voltage and coulomb count of up to 14 battery cells stacked in series with zero desynchronization between samples. Figure 4 shows the primary functional architecture of the L9963E, which can control up to seven NTC thermistors and communicates with the host BMS microcontroller via SPI or an optically isolated interface.

Figure 4: Functional block diagram of the STMicro L9963E automotive qualified multicell battery monitoring and balancing IC (source: ST).
Up to 31 L9963E devices can be star-connected to monitor 434 cells connected in series. A 16-bit ADC provides a maximum error of ±2 mV across the entire measurement range of 0.5 to 4.3 V. The L9963E also provides a passive 200 mA cell balancing function for discharge via an internal path or a higher current through externally connected MOSFETs.
Another example of an automotive battery control and balancing IC (AEC-Q100, ISO26262, and ASIL-D) is the TLE9012DQU from Infineon Technologies (Figure 5).

Figure 5: Infineon's TLE9012DQU IC provides multi-channel control and balancing of lithium-ion batteries (source: Infineon Technologies).
The TLE9012DQU can monitor the voltage of 12 lithium-ion cells connected in series and features an independent 16-bit sigma-delta ADC for each cell. The device also integrates five temperature measurement channels for use with external NTC thermistors. Passive cell balancing is up to 200 mA per cell. An evaluation board based on the TLE9012DQU is available for prototyping.
Texas Instruments' BQ769xc series components are also automotive battery control ICs. Designed for use with lithium-ion and lithium-phosphate cells, the BQ769x series allows for the serial connection of up to 16 cells. The BQ769x incorporates a full analog front panel with a 14-bit ADC.
The BMS: Vital for Optimizing Electric Vehicle Battery Performance.
Electric vehicle battery management systems play an essential role: they monitor, control, and optimize the vehicle's battery pack to achieve the best balance between power output and range, while also fulfilling a vital safety function. For more information on battery management techniques, readers may find this Synopsys white paper helpful .
